Amp Section

General information

Within each Machine, the sound source goes through a Filter section and is then routed to the same Amp section.
Each Amp section is then routed to the Mixer.

The filterAmp section hasoffer 3settings pages containing different controls. When a Tab header displays small bar icons, click its corresponding button underneathrelated to jumpamplitude betweenand its pages.

Page 1:
distortion:

FilterDrive 1 FrequencyType	Filter 1 ResonanceDrive	(Filter Morph) -or- (Filter Gain)DCA1	Filter 1 TypeDCA2
ControlsSelect one of the filter's29 cutoffdistortion frequency	Controls the filter's resonance amount	Morph between the filter types, from Low-Pass to Notch to High-pass. This parameter is only available when the filter type is set to SVF for State Variable Filter. -or- Set the EQ gain. This parameter is only available when the filter type is set to Bell EQ.	Select a filter type and slope.algorithms. Read the chart below for details onregarding everyeach filterone. available.	Controls the amount of distortion	The first Digitally Controlled Amplifier. DCA1 and DCA2 are routed in series, with 1 usually modulated by velocity and 2 modulated by an envelope. But you can set modulations as you wish.	The second Digitally Controlled Amplifier. DCA1 and DCA2 are routed in series, with 1 usually modulated by velocity and 2 modulated by an envelope. But you can set modulations as you wish. This parameter cannot be modulated.

PageDistortion 2 is the same as page 1, but controls Filter 2. In order to unlock it, you need to have the Routing on page 3 on a setting other than Single.

Filter typesalgorithms reference:

1-bandequalizertoincreasedecreaseselectedregion.2willadjustthebellwidthandKnob3willthegain

Off	SVFSoft	K35 LP12 / HP6Medium	TLD LP 6/12/18/24Hard	TLD N 12/24Diode
The filterDrive section is bypassed	State Variable Filter model. Use Knob 3 to morph between filter types???	Korg 35. Inspired by the MS-20 filter.  ???	Transistor Ladder Filter model. Inspired by the classic Moog filter. Low-Pass with a selection of slopes from 6dB/oct to 24/dB/oct???	Transistor Ladder Filter model. Inspired by the classic Moog filter. Notch filter with 12dB/oct and 24dB/oct slopes???
TLD BP 12/24Demon	DLDSoft LP24Fold	COMBDiode +/-Fold	FORMANTDual Frequency	BELL EQTube
Transistor Ladder Filter model. Inspired by the classic Moog filter. Band-pass with 12dB/oct and 24dB/oct slopes ???	Diode Ladder Filter model. Inspired by the TB-303 filter. Low-pass with a steep 24dB/oct slope.???	Comb filter for hollowed-out sounds and wooshes effects. With positive or negative feedback (resonance)???	Formant filter for vowel sounds. Morph through A-E-I-O-U with Knob 1.???	Simple???
Sigmoid	Tape orDynamics	Tape aHysteresis	Tape frequencyCurve	Tape KnobNoise
???	???	???	???	???
Hard setClipping	Fuzz	Chebyshev	Half Rectifier	Full Rectifier
???	???	???	???	???
Transistor	Dynamic	Asymmetric	Feedback	Zero Crossing
???	???	???	???	???
Bit Reaper	Sample Reaper	Sample Reduction	Bitwise	Ring Modulation
???	???	???	???	???

Page 3 allows for filter routing options:

Routing	Balance between filter 1 and 2	-	-
Select a routing configuration for the filters. Single enables only filter 1. Serial routes the output of Filter 1 to Filter 2. Para will route both filters in parallel Split will split the sound sources into the two filters, depending on the Machine select.	Controls the volume of both filters at the output. Fully clockwise only filter 2 will be heard, and fully counter-clockwise it will be only filter 1.	-	-