LFO Wavetable

This is a Low-Frequency Oscillator with(LFO) that provides a multitudewide range of waveshapes accessiblewaveforms through wavetables.

Main features of this LFO:

• Any wavetable can be used, allowing you to browse and select individual waves as modulation sources.
• In Free (notmode, synchronized)multiple modefrequency the LFO goes from 0Hz (the LFO is frozen) into audio rate, with a maximum of 81,900Hz
  Thereranges are alsoavailable:
  - synchronizationSlow: 0.0003 Hz to 2.22 kHz
  - Medium: 0.01 Hz to 81.9 Hz
  - Fast: 0.5 Hz to 4095 Hz
• Synchronization options to syncallow the LFO to sync to an incoming MIDIexternal clock (ifsignal.
you have the expander) // If no expander the options appears or does not ?// or
• Syncing to the Voice's main oscillator frequency.frequency is possible, enabling FM-like modulation (0.25× to 24× the oscillator frequency).
• The LFO can be retriggered at the start by a trigger source (note, clock, or gate input).

Main screen of the Wavetable LFO

On any page of the LFOWavetable Wavetable,LFO, turn the Encoder to scrollbrowse through wavetables. You can clickClick the Encoder to bring upaccess the Browser and manually load a wavetable manually. wavetable.
When in
In the Browser:
- usePress Button 1 to gonavigate up a levelfolder inlevel.
- the file system,Press Button 4 to enable AutoloadAutoload, so you can listen to the results inallowing real-time,time clickauditioning.
- Click the Encoder to open thea selected folder or load thea selectedchosen wavetable file.

Wave/Speed Tab

HereThis section allows you canto set theconfigure basic parametersLFO of the LFO:parameters:

	Wave		Phase		Speed / Clock / Ratio		-
Select thean LFO wave by navigating the wavetablewavetable.	MoveAdjust the phase offset, shifting the starting point of the LFO waveshape forward or backward in timewaveform.	Select the frequency of the LFO. Depending of the selected synchronisation Mode in the Settings tab, this parameter will have a different name and function In Free mode, selectsSet the LFO frequency. This parameter adapts based on the synchronization mode: Free mode: frequency in Hertz InHz Clock mode, selects the LFO frequency inmode: divisions or multiplications of the MIDI Clock In Ratio mode,mode: selects the LFO frequency in a multiple of frequencymultiples of the Voice's mainoscillator oscillatorfrequency	-

Settings Tab

HereThis yousection can choosedefines the LFOLFO's run mode and howretrigger itbehavior. retriggers.These Note that these parameterssettings cannot be modulated.

Mode	Trigger	-	-
Mode	Trigger	-	-
SelectChoose the LFO synchronisationsynchronization mode. mode: Free: means theThe LFO isruns notindependently. synced Clock: means theThe LFO is synchronizedsyncs to the incoming MIDI Clock signalsignal. Ratio: means theThe LFO is syncedsyncs to the Voice's mainoscillator oscillator,frequency, and thus trackstracking its pitch.pitch This is intended(useful for FM, AMAM, and other kinds of audio-rate modulationmodulations).	SelectDefines athe source tothat reset the phase of the LFO. It can be any of the Gate inputs, the same signal as Voice trigger, or a selection of MIDI Clock divisions and multiplications This parameter is only available whenresets the LFO isphase. Options include: Any Gate input Voice trigger signal MIDI Clock divisions/multiplications Only available in Free modemode.	-	-

Output Tab

Here you can sculptModify the LFO signal before it'ssending sentit to the modulation targets:

Polarity	Gain	-	-
PolaritySelect LFO polarity: Bipolar Unipolar positive Unipolar negative	Gain	-	-
SelectAdjust the LFO polarity between bipolar, unipolar positive and unipolar negative	Set theoutput level of the LFO. Can(can be modulatedmodulated).	-	-